模具专业英语详解

优胜设计史勇老师

模具述语

一、入水：gate

进入位：gate location

水口形式：gate type

大水口：edge gate

细水口： pin-point gate

水口大小：gate size

转水口：switching runner/gate

唧嘴口径：sprue diameter

二、流道: runner

热流道：hot runner,hot manifold

热嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圆形流道：round(full/half runner

流道电脑分析：mold flow analysis

流道平衡:runner balance

热嘴：hot sprue

热流道板：hot manifold

发热管：cartridge heater

探针: thermocouples

插头：connector plug

插座： connector socket

密封/封料： seal

三、运水：water line

喉塞：line lpug

喉管：tube

塑胶管：plastic tube

快速接头：jiffy quick connector plug/socker

四、模具零件：mold components

三板模：3-plate mold

二板模：2-plate mold

边钉/导边：leader pin/guide pin

边司/导套：bushing/guide bushing

中托司：shoulder guide bushing

中托边L：guide pin

顶针板：ejector retainner plate

托板：support plate

螺丝： screw

管钉：dowel pin

开模槽：ply bar scot

内模管位：core/cavity inter-lock

顶针：ejector pin

司筒：ejector sleeve

司筒针：ejector pin

推板：stripper plate

缩呵：movable core,return core core puller

扣机（尼龙拉勾）：nylon latch lock

斜顶：lifter

模胚（架）： mold base

上内模：cavity insert

下内模：core insert

行位（滑块）： slide

镶件：insert

压座/斜鸡：wedge

耐磨板/油板：wedge wear plate

压条：plate

撑头: support pillar

唧嘴： sprue bushing

挡板：stop plate

定位圈：locating ring

锁扣：latch

扣鸡：parting lock set

推杆：push bar

栓打螺丝：S.H.S.B

顶板：eracuretun

活动臂：lever arm

分流锥：spure sperader

水口司:bush

垃圾钉：stop pin

隔片：buffle

弹弓柱：spring rod

弹弓:die spring

中托司：ejector guide bush

中托边：ejector guide pin

镶针：pin

销子：dowel pin

波子弹弓：ball catch

喉塞: pipe plug

锁模块：lock plate

斜顶：angle from pin

斜顶杆：angle ejector rod

尼龙拉勾：parting locks

活动臂：lever arm

复位键、提前回杆：early return bar

气阀：valves

斜导边：angle pin

术语：terms

承压平面平衡：parting surface support balance

模排气：parting line venting

回针碰料位：return pin and cavity interference

模总高超出啤机规格：mold base shut hight

顶针碰运水：water line interferes withejector pin

料位出上/下模：part from cavith (core) side

模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.

不准用镶件： Do not use (core/cavity) insert

用铍铜做镶件： use beryllium copper insert

初步（正式）模图设计：preliinary (final) mold design

反呵：reverse core

弹弓压缩量：spring compressed length

稳定性好：good stability,stable

强度不够：insufficient rigidity

均匀冷却：even cooling

扣模：sticking

热膨胀：thero expansion

公差：tolorance

铜公(电极)：copper electrode

油壓缸：CYLINDER

直角定位:STRAIGHT SIDE INTERLOCKS

模胚: MOLD　BASE

后模：CORE

前模: CAVITY